Ocala, FL · Garage Floor Coatings

Epoxy Flooring in Ocala, FL

Garage floors, lanais, and pool decks coated the slow, right way: ground, repaired, tested for moisture, and priced in writing before we start.

Get a Free Estimate

Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.

Rather talk? Call (352) 555-0148.

Diamond-Ground Prep on Every FloorWritten Price Before Work StartsOne Crew, Start to FinishFree In-Home Estimates

A floor that stays down starts under the coat

Most garage floors that peel were never given a chance. The coat went on over a smooth, sealed slab, and hot tires and Florida heat did the rest. We do it the other way: the slab gets ground, repaired, and tested first, and the coat goes on a floor that is ready to hold it.

Ocala is growing fast, and a lot of our work is brand-new garage slabs in new subdivisions. A new slab is the best floor you will ever coat — no oil, no old paint, no years of stains — as long as the curing seal comes off and the moisture reads right first.

We also coat the floors Ocala homes live on outside the garage: lanais, patios, and pool decks, farm workshops and barn floors, and work floors for local shops. One crew runs your job from the grind to the walkthrough.

Every job starts the same way: we come look at the floor, measure it, and give you a written price. No pressure at the door, and the price does not change once work starts. Start with the garage floor page or the cost guide, or just call and tell us about your floor.

With Ocala Epoxy Floors vs. a typical low-bid coating

The low bid is not low by luck. Something got skipped, and in Florida the skipped step is the one that holds the floor down. Here is the side-by-side we would want if we were buying.

With Ocala Epoxy FloorsA typical low-bid coating
PrepDiamond grind on the whole slab, every jobAcid etch, or a quick sweep and roll
MoistureSlab tested before we coat; barrier primer when the reading calls for itNo test — the slab is coated damp or dry, same way
CracksChased, filled, and ground flush before coatingCoated over and left to show through
Flake coverFull broadcast, wall to wall, until the coat can hold no moreA light sprinkle that shows the base coat through it
TopcoatClear, sun-stable topcoat that holds its color at the door linePlain epoxy that ambers in the sun
PriceWritten and all-in before work startsLow number up front, add-ons later
CrewOne crew, start to finishWhoever is free that week

Recent floors around Ocala

Garages, a lanai, a pool deck, and a barn floor. Drag the slider on any card to see the same floor before the coat.

Finished full-flake garage floor in Ocala
The same Ocala garage floor before coating
BeforeAfter

Two-car garage, full-flake system

440 sq ft · Final price $3,400

The slab had two long cracks and dark stains where the tires sit. We ground the floor, filled the cracks, and ran a full-flake system with a polyaspartic topcoat.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Finished polyaspartic garage floor in Belleview
The same Belleview garage floor before coating
BeforeAfter

Two-car garage, polyaspartic system

440 sq ft · Final price $3,950

A thin paint coat from years back was lifting at the door line. We ground it all off and tested the slab for moisture. Then we laid a polyaspartic system that holds its color in the sun.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Finished flake lanai floor in Summerfield
The same Summerfield lanai floor before coating
BeforeAfter

Lanai floor, full-flake system

200 sq ft · Final price $1,750

The bare slab stained fast and felt slick when wet. We ground it, sealed it with a full-flake system, and added grip to the topcoat for wet feet.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Finished garage floor in a new Marion Oaks home
The same new Marion Oaks garage slab before coating
BeforeAfter

One-car garage in a new build, full-flake system

240 sq ft · Final price $1,950

A brand-new slab, coated before the first oil drip ever hit it. We ground off the curing seal, checked the moisture, and ran a full-flake floor while the house was still empty.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Finished coated pool deck in Silver Springs
The same Silver Springs pool deck before coating
BeforeAfter

Pool deck, polyaspartic system

600 sq ft · Final price $5,400

The old deck paint was chalky and hot underfoot. We ground it back to bare concrete. Then we coated the deck with a sun-stable system and a grip finish for wet feet.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.
Finished solid-color epoxy workshop floor in McIntosh
The same McIntosh workshop floor before coating
BeforeAfter

Barn workshop floor, solid-color epoxy

660 sq ft · Final price $3,900

A working barn floor with oil stains and a cracked aisle. We ground out the stains, rebuilt the cracked spots, and laid a solid-color floor that hoses clean.

Representative job — an example of the work and pricing on this site, replaced with verified job records as they close.

How a floor gets done

1

Measure and read the slab

We come out, measure the floor, and read the slab: cracks, stains, old coats, and moisture. You pick the system and the flake from real samples, and you get a written, all-in price before any work starts.

2

Grind and repair

We diamond-grind the whole slab so the coat can grip into the concrete, not sit on top of it. Cracks and pits get filled and ground flush. Old paint and failed coats come all the way off.

3

Coat and broadcast

Base coat goes down at full build. On flake floors, we spread flake wall to wall until the wet coat can hold no more, then let it cure, scrape it back, and vacuum it clean.

4

Topcoat and walkthrough

A clear, sun-stable topcoat seals the floor, with grip added where the floor gets wet. We walk the floor with you, go over care, and put your back-in-use times in writing.

What we put in writing

A floor is a big spend on a house, and you should not have to take any of it on faith. These four things are part of every job we run, and they are in writing before the grinder ever starts.

  • Written, all-in price after an in-person look — before any work starts, not after
  • Diamond-grind prep on every floor — no etch-and-roll shortcuts
  • Moisture test on Florida slabs before we coat
  • A final walkthrough with you, and back-in-use times in writing

Questions we hear

How much does a garage floor cost?

It turns on size, the shape the slab is in, and the system you pick. A two-car garage in full flake runs $2,640 to $4,180 at our rates. Your exact number comes after we look at the floor, in writing, before work starts. The calculator below gives you a planning range right now.

How long does the job take, and when can I park on it?

Most garages take a few days of work, start to finish. Walk times and park times depend on the system: polyaspartic tops cure fast, and many garages are back in use the next day. Your schedule is confirmed in writing at the estimate, so you can plan around it.

Will it peel like the kit I tried?

Kits peel because the slab under them was smooth and the coat never got a grip. We grind the whole slab, fill the cracks, and test for moisture before we coat. That prep is the whole difference, and it is why our floors stay down.

Where do I put everything in my garage?

The garage has to be empty on grind day. Most folks use the lanai, a side room, or a rented pod in the driveway for a few days. We will talk through the plan at the estimate so install day has no surprises.

Is the floor slippery when it is wet?

A full-flake floor has texture built in, and we add grip to the topcoat on floors that get wet — lanais, pool decks, and garage entries. Tell us how the floor gets used and we will spec the finish for it.

Will the floor yellow in the sun?

Plain epoxy ambers where sun hits it, worst at the garage door line. Every floor we coat gets a sun-stable topcoat, so the color at the door matches the color at the back wall.

Can you coat over my old paint or failed epoxy?

Yes — that is a big part of our work. The old coat comes all the way off with the grinder, the slab gets repaired, and then the new system goes on a clean, open slab.

Estimate Calculator

Pick your floor and its size. The range updates as you go.

Add-ons your floor may need

Your planning range —

Every floor is different. Slab condition moves the final number more than size does.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

Call (352) 555-0148 Estimate Calculator