Two-car garage, full-flake system
The slab had two long cracks and dark stains where the tires sit. We ground the floor, filled the cracks, and ran a full-flake system with a polyaspartic topcoat.
The core job we do: a garage slab ground, repaired, and coated so it stays down through Florida heat and hot tires.
Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.
Rather talk? Call (352) 555-0148.
A garage floor coating is a resin system built on your slab: grind, repair, base coat, finish, and a clear top. Done right, it shrugs off oil, hot tires, and dropped tools, and it hoses clean in minutes. Done cheap, it peels in sheets by the second summer.
Most Ocala garages get our full-flake system: an epoxy base, flake spread wall to wall, and a polyaspartic top. Flake hides the small flaws every slab has, adds grip, and reads like stone. Solid color is the plain, clean pick for shops and work garages.
Garages here work hard. They hold cars, golf carts, freezers, feed, tack, and half the tools a family owns. The floor has to take all of it, plus August heat on the tires. Our take, after a lot of redos of other folks' work: the system matters less than the slab under it. We spend the time on the grind.
Redo work is welcome here. If a kit or a cheap coat is lifting, we grind it off and start clean — see repair and removal. New-build garages are the other sweet spot: coat the slab before oil ever touches it.
We come out, measure the floor, and read the slab: cracks, stains, old coats, and moisture. You pick the system and the flake from real samples, and you get a written, all-in price before any work starts.
We diamond-grind the whole slab so the coat can grip into the concrete, not sit on top of it. Cracks and pits get filled and ground flush. Old paint and failed coats come all the way off.
Base coat goes down at full build. On flake floors, we spread flake wall to wall until the wet coat can hold no more, then let it cure, scrape it back, and vacuum it clean.
A clear, sun-stable topcoat seals the floor, with grip added where the floor gets wet. We walk the floor with you, go over care, and put your back-in-use times in writing.
Three things kill garage floors in Ocala, and the system has to answer all three. Hot tires can soften a thin coat and lift it in small crescents where the wheels sit. Sun at the door line ambers plain epoxy, so the first few feet turn a different color. And ground moisture pushes up through the slab and blisters a coat from below.
The answers are built into the job, not sold as extras: a full-build system with a hard top for the tires, a sun-stable clear coat for the door line, and a moisture test — with a barrier primer when the reading calls for it — before anything goes down.
The slab had two long cracks and dark stains where the tires sit. We ground the floor, filled the cracks, and ran a full-flake system with a polyaspartic topcoat.
A thin paint coat from years back was lifting at the door line. We ground it all off and tested the slab for moisture. Then we laid a polyaspartic system that holds its color in the sun.
A brand-new slab, coated before the first oil drip ever hit it. We ground off the curing seal, checked the moisture, and ran a full-flake floor while the house was still empty.
Tell us about the floor. We call back with a time to come look — the written price comes after the in-person look, before any work starts.
Rather talk? Call (352) 555-0148.
It depends on the system. Floors topped with polyaspartic cure fast, and many garages take a car again the next day. Full epoxy builds need more time. Your exact walk and park times come in writing at the estimate.
One, two, and three-car garages, plus tandem and workshop bays. The calculator below prices by size. Oversize and farm garages get measured at the visit and priced from the same rates.
The floor has to be clear on grind day. Most folks stage things on the lanai, in a side room, or in a driveway pod for a few days. We plan it with you at the estimate.
No. Stains get ground out or sealed in prep, and the finished floor is non-porous — oil wipes up instead of soaking in. Old, deep oil can need extra grind time, and we will show you at the visit.
We can, but a seam mid-floor shows and wears first. Most folks coat the whole slab while the garage is empty anyway. We will talk through it honestly at the look.
Pick your floor and its size. The range updates as you go.
Add-ons your floor may need
Every floor is different. Slab condition moves the final number more than size does.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.